Zhejiang Matech Industry Company Limited

TEL: +86-571-28350111
Categories
Contact Us
Hangzhou Matech Steel Company Limited
Tel: +86-571-28350111
Fax: +86-571-86693517
Email: sales@matech-steel.com
Add: Floor 10, Xixi Vally E-Building, Xihu District, Hangzhou, Zhejiang province, China
ASTM A234 WPB Fittings

ASTM A234 WPB Fittings

ASTM A234 WPB Standard Specification ASTM A234 WPB is the Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High Temperature Service. ASTM A234 WPB Concentric Reducer ASTM A234 WPB Concentric Reducers are used for connecting pipes of different...

ASTM A234 WPB Standard Specification

ASTM A234 WPB is the Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High Temperature Service.

图片23.png 

ASTM A234 WPB Concentric Reducer

ASTM A234 WPB Concentric Reducers are used for connecting pipes of different diameters and find wide applications in various chemicals, construction industries, paper, cement & ship builders.

图片24.png 

ANSI B16.9 ASTM A234 WPB Eccentric Reducer

ANSI B16.9 ASTM A234 WPB Eccentric Reducer with A234 WPB and 1/2 to 56-inch Size (DN15 to DN1400)

图片25.png 

A234 WPB Large Diameter Pipe Cap

A234 WPB Large Diameter Pipe Cap manufactured using superior grade raw materials.

图片26.png 

A324 WP11 elbow

A324 WP11 elbow is the manufacturing process of ASTM A234 WPB.

ASTM A234 Scope

1.1 This specification covers wrought carbon steel and alloy steel fittings of seamless and welded construction covered by the latest revision of ASME B16.9, B16.11, MSS-SP-79, MSS-SP-83, and MSS-SP-95. These fittings are for use in pressure piping and in pressure vessel fabrication for service at moderate and elevated temperatures. Fittings differing from these ASME and MSS Standards shall be furnished in accordance with Supplementary Requirement S58 of Specification A 960/A 960M.
1.2 Optional supplementary requirements are provided for fittings where a greater degree of examination is desired. When desired, one or more of these supplementary requirements may be specified in the order.
1.3 This specification does not cover cast welding fittings or fittings machined from castings. Cast steel welding fittings are governed by Specifications A 216/A 216M and A 217/A 217M.
1.4 This specification is expressed in both inch-pound units and in SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units.
1.5 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

GENERAL NOTE:
All values are maximum unless otherwise indicated.

Chemical Composition (%) of ASTM A234

Grade

C

Mn

P

S

Si

Cr

Mo

Ni

Cu

V

Nb

WPB

0.3

0.29-1.06

0.05

0.058

0.1min

0.4

0.15

0.4

0.4

0.08

0.02

WPC

0.35

0.29-1.06

0.05

0.058

0.1min

0.4

0.15

0.4

0.4

0.08

0.02

WP11 CL1

0.05-0.15

0.30-0.60

0.03

0.03

0.50-1.00

1.00-1.50

0.44-0.65

-

-

-

-

WP11 CL2/3

0.05-0.20

0.30-0.80

0.04

0.04

0.50-1.00

1.00-1.50

0.44-0.65

-

-

-

-

Notes:

· For each reduction of 0.01% below the specified C maximum, an increase of 0.06% Mn above the specified maximum will be permitted, up to a maximum of 1.35%.

· The sum of Cu, Ni, Cr, and Mo shall not exceed 1.00%.

· The sum of Cr and Mo shall not exceed 0.32%.

· The maximum carbon equivalent (C.E.) shall be 0.50, based on heat analysis and the formula C.E.=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15.

Mechanical properties of ASTM A234

Tensile Requirements

WPB

WPC, WP11CL2

WP11CL1

 WP11CL3

Tensile Strength, min, ksi[MPa]

60-85

70-95

60-85

 75-100

(0.2% offset or 0.5% extension-under-load)

[415-585]

[485-655]

[415-585]

 [520-690]

Yield Strength, min, ksi[MPa]

32

40

30

45

[240]

[275]

[205]

[310]

Where the wall thickness lies between two values above, the min elongation value is determined by the following equations:

· Longitudinal E=48t+15.00

· Transverse E=32t+10.00

· E = elongation in 2in [50mm], %

· t = actual thickness of specimen, in [mm]

Steel elbow is used to be installed between two lengths of pipe or tube allowing a change of direction,usually these carbon steel elbows distinguished by connection ends, The ends may be machined for butt welding , threaded , or socketed , so the carbon steel elbows are consist of butt weld,thread elbow socket elbow and other series.the material is selected according to the application use such as high temperature use,sanitary fitting,regular industrial use etc.

What is the manufacturing process of ASTM A234 WPB pipe fittings?

The WPB is not short hand for any process. It is simply an identifier developed by ASTM. The fittings in question are manufactured in the same manner as the companion pipe for this specification.

In very large sizes, the fittings may be manufactured in pieces and welded together as is the case for many large fittings.

The term used for the manufacturing is called “wrought” which means it is worked as opposed to being cast or forged.

As to the W standing for weldable, I’m not sure that is correct since that are many, many pipe fittings that are weldable but carry designations other than a W. Note the reference below.

Forging is the manufacturing process of ASTM A234 WPB pipe fittings.

W = WELDABLE / wrought

P = RELATED TO P NUMBER OF ALLOY MATERIAL

B = REFER TO MINIMUM YIELD OF MATERIAL

LATEST STANDARD IS:

ASTM A234/A234M-07 Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High Temperature Service

This standard covers wrought carbon steel fittings of seamless and welded construction which are manufactured to the dimensional specifications of ASME B16.9 and B16.28. These fittings are primarily for use in pressure piping and in pressure vessel fabrication for service at moderate and elevated temperatures.

Hot Tags: ASTM A234 WPB fittings, China, manufacturers, suppliers, factory, wholesale
Related Products
  • Contact Us
    Hangzhou Matech Steel Company Limited
    Tel: +86-571-28350111
    Fax: +86-571-86693517
    Email: sales@matech-steel.com
    Add: Floor 10, Xixi Vally E-Building, Xihu District, Hangzhou, Zhejiang province, China
  • Categories
  • Copyright © Hangzhou Matech Steel Company Limited All Rights Reserved.